OP,Operational,Power,denthelp.it,High,Electronics , Home Audio,AMP,/exactor77003.html,Taidacent,OPA541,Monolithic,Amplif,$42 Taidacent OPA541 OP AMP High In a popularity Operational Power Monolithic Amplif $42 Taidacent OPA541 OP AMP High Power Monolithic Operational Amplif Electronics Home Audio $42 Taidacent OPA541 OP AMP High Power Monolithic Operational Amplif Electronics Home Audio Taidacent OPA541 OP AMP High In a popularity Operational Power Monolithic Amplif OP,Operational,Power,denthelp.it,High,Electronics , Home Audio,AMP,/exactor77003.html,Taidacent,OPA541,Monolithic,Amplif,$42

Taidacent OPA541 Brand Cheap Sale Venue OP AMP High In a popularity Operational Power Monolithic Amplif

Taidacent OPA541 OP AMP High Power Monolithic Operational Amplif

$42

Taidacent OPA541 OP AMP High Power Monolithic Operational Amplif

|||

Product Description

Description

The OPA541 module is a power operational amplifier that can work with a power supply up to 40 V and provide a continuous output current of up to 5A. The internal current limiting circuit can be controlled by the user using a single external resistor, thereby protecting the amplifier and load from fault conditions. It is suitable for motor drive speaker drive, transformer drive and audio amplifier. It can also amplify triangle wave, sine wave, and square wave signals.

Module model OPA541
Module type low frequency power amplifier
Input signal form single-ended
Input voltage range 2Vpp (MAX); generally within the power supply range
Module input impedance 1K ohm
Module supply voltage ± 10V ~ ± 40V
Module supply current ± 5A; large output current requires large supply current
Module output impedance low impedance
Output voltage range 68Vpp (MAX); in the case of positive and negative 40V power supply
Output current 5A (MAX)
Output power 50W (MAX)
Module gain 33 times; the default gain is 33 times, the first level is 11 times, the second level is 3 times, G1 = R1 / R2 + 1, G2 = R7 / R4 + 1
Input offset voltage 200uV (MAX)
Input offset drift 2uV / ℃ (MAX)
Input bias current 125nA (MAX)
Input voltage noise 35nV√Hz (1KHz)

Module weight: 125g

Module protection: none; no reverse connection protection, unlimited current protection

Module weight: 125g

Module specifications: 96 * 64 * 41mm; length * width * height-PCB size

The module becomes hot: there is a heat sink, and forced air cooling is required at high current

Module heating factors: the input and output voltage is too large or the module is damaged

Module working temperature: -40 ℃-+ 75 ℃ industrial grade

Module features: positive and negative power LED indication

Application range: small signal amplification, audio signal amplifier, motor drive, servo amplifier, etc.

Module interface type: SMA signal signal input and output, 5.08 blue power card wire holder

Interface diagram

High Power Audio AmplifierHigh Power Audio Amplifier

FAQ

Q: Is the magnification fixed? How to adjust?

A: The default magnification of the module is 33 times. If you need to adjust the magnification, you can only replace the resistor on the board. The original resistor is 0805. The calculation formula is given in the parameter details.

Q: Can the module directly drive the coil?

A: The module can drive the coil, but the internal resistance of the coil is required to be greater than 4 ohms. If it is less than 4 ohms, a series power resistance is required, otherwise the module may be damaged.

Q: Can the module amplify square wave or pulse? What is the module bandwidth?

A: The module can amplify low-frequency square waves or pulses. Because it is an audio amplifier, the total bandwidth is not high. Signals within 100K can be amplified. The module is compatible with DC input.

Q: Can the module be enlarged 1: 1? That is, only the current is amplified. ?

A: The module can support 1: 1 amplification. You need to modify the resistance configuration magnification yourself. It is not recommended to directly configure the op amp follow mode, which is easy to self-excitation. It is recommended to change to resistance attenuation first, and then operation amplification; the total gain is 1 Just fine.

Q: Why the input sine wave output is square wave? What is the output current? What is the output power?

A: Generally speaking, the input signal is too large, and the op amp is amplified to the cut-off distortion, which is the square wave, or the supply voltage is not enough. Can reduce the input signal and increase the supply voltage to solve. The output current of the module is determined by the output voltage and the load. I = Uout / R. Similarly, the output power P = U * I is also determined by the output voltage and the load resistance. When high power is input, heat dissipation grease and air cooling can be added.

Q: Can I use the second level directly instead of the first level?

A: You can use the second stage directly, but you need to remove the chip of the first stage, and then input the signal from OUT1. Otherwise, the first-level chip will affect the signal input.

Precautions for using the module

(1) The power consumption of the module is large, and the power supply needs to have a certain margin. It is recommended to use a power supply with a current drive capacity greater than twice the output current. The module can only be powered by dual power supplies.

(2) In order to avoid unnecessary interference, it is recommended to use a linear power supply, the power supply cannot exceed plus or minus 40V.

(3) It is recommended to use the SMA to BNC cable to directly observe the output signal for the output signal. Poor contact or poor quality wires may cause signal attenuation or excessive noise.

(4) The SMA port is not available for power output, and a blue terminal block must be used. The SMA port is for observing the signal and must not overpower.

(5) Due to the large power consumption and heat generation, pay attention to ventilation and heat dissipation for long-term work, and add fans to strengthen heat dissipation if necessary.

(6) Since the module has a fixed magnification and no external protection circuit, it is recommended to confirm the output power and amplitude before loading to avoid damage to the module.

Taidacent OPA541 OP AMP High Power Monolithic Operational Amplif

Updates